Altoona Hoist & Crane
FOR SERVICE CALL, 24/7:
(814) 696-0350 or (800) 246-5982
Photo Gallery of Just a Few of Our
Overhead Crane and Hoist Projects
A New 5-Ton capacity top running, single girder crane. this crane was designed and fabricated at our old shop.
Setting a New 15-Ton Top Running, Single Girder Crane on the Runway. Everything, including the Free Standing Runway System, was installed by our skilled Technicians
A damaged bottom block on a 150-Ton Crane. Notice the bent sheave (5th from the left). The hoist was double-blocked due to a faulty limit switch. Fortunately, no one was hurt. Our Technicians replaced the damaged sheave and repaired the limit switch.
Final Installation of a 20-Ton, Offset Leg Outdoor Gantry Crane with dual 10-Ton Hoists. This unit was one of the first projects designed and fabricated at our new shop. Note the left leg is 4-feet higher than the right leg. This project provided a real design challenge
This 5-Ton capacity system was installed in a maintenance facility in Maryland. The entire runway structure and crane were designed and fabricated at our shop. The complete system was installed by our skilled Technicians.
This is a simple 500-LB capacity, single girder, underhung system designed and fabricated for a local extrusion facility. Notice the hard working Altoona Hoist Technician in the lower right corner.
One of two 45-Ton capacity, 75' span top running double girder cranes installed by our crew at a steel processing facility near Altoona.
This is a 2-Ton capacity single girder underhung crane being installed at a pump repair facility.
An example of a Gorbel pre-engineered workstation crane we installed at a facility in Bedford, PA.
Here is a 3-Ton capacity system designed, fabricated, and installed for a local entrepreneur in his new shop
A 3-Ton top running single girder crane in final assembly. This crane was designed and fabrication was started while we were still at our old Shop. Final assembly was done at our new Shop
Setting the second 2-Ton capacity crane on a new runway structure designed, fabricated, and installed by our Technicians
One of five, 5-Ton capacity cranes and runway systems designed, fabricated, and installed for a customer in Johnstown, PA
This is an older 20-Ton capacity top running double girder crane we refurbished and put back into service at a Hollidaysburg, PA manufacturing facility, in their new addition. Our Engineers worked with the building Designers and designed the new runway system which was then fabricated and installed by us.
Here we just finished setting this 5-Ton capacity, 55' span outdoor crane. The hoist was equipped with stainless steel wire rope, sheaves, and drum to endure the harsh outdoor environment.
This is a 2-Ton capacity system designed for use in a forklift battery changing room. The crane and the entire support structure was designed, fabricated, and installed by Altoona Hoist
Here we are setting the first of two 10-Ton single girder top running cranes at a steel fabrication facility north of State College, PA
This is a 10-Ton capacity, Patented Track crane system we built and installed at a water treatment facility in Columbus Ohio.
Flying a 20-Ton capacity double girder top running crane into place at another water treatment facility in Ohio
Putting the final touches on a 20-Ton capacity double girder crane designed and fabricated at our Duncansville Shop
A dual 10-Ton Patented Track Monorail system used for pump maintenance at a water treatment facility
Packed and ready to go. Two 10-Ton capacity cranes loaded on the truck and heading for the jobsite
This Website and its contents, in their entirety, are the property of Altoona Hoist and Crane. Any duplication is prohibited without written consent.
Altoona Hoist & Crane
PO Box 248, 3269 Rt-764
Duncansville, PA 16635
Ph: (814) 696-0350 (800) 246-5982
Fax: (814) 696-0370